VSAN Electriclas & Sensors

About Us

We “Vsan Electricals & Sensors” are a “Sole Proprietorship” based firm, engaged as the manufacturer of Flow Meter, Level Transmitter, Float Switch and many more. In order to keep pace with the never-ending demands of customers, we are involved in offering a wide range of these products. Our offered products are widely known for their impeccable quality, seamless finish and best-grade material. We are also providing Installation Service and Flow Meter Repairing Service.

Quality Policy

VSAN will provide value and satisfaction to customers on products and services. This will be achieved through:

>> Systematic training and motivation of employees.
>> Complying with customer requirements and applicable statutory/regulatory requirements.
>> Continually improving the efficiency and effectiveness of the Quality Management Systems

Manufacturing Principles

  >> Oval Gear flow meter

  Oval gear meters measure flow by employing a geared rotor to pass known volumes of a fluid through a housing. The oval gear flow meter comprises oval-shaped, geared rotors which rotate within a housing of specified geometry. ... Capillary action of the metered fluid forms a liquid seal

          Working Principles

          Product

  >> Mass Flow Meter

  Coriolis mass flow measuring principle. A Mass Flow Meter operating on the "Coriolis principle" contains a vibrating tube in which a fluid flow causes changes in frequency, phase shift or amplitude.

          Working Principles

          Product

  >> Float switch

  We recommend our float type level switch for low cost liquid measurement. The principle of float typelevel meter is that a float moves up and down due to buoyancy. A reed switch in a stem is actuated by a magnet in the float, and outputs detection signal (see the figure below)

          Working Principles

          Product

  >> Ultrasonic level sensor

  Ultrasonic level sensors work by the "time of flight"principle using the speed of sound. The sensoremits a high-frequency pulse, generally in the 20 kHz to 200 kHz range, and then listens for the echo. The pulse is transmitted in a cone, usually about 6° at the apex.

          Working Principles

          Product

  >> Ultrasonic Flow Meter

  Ultrasonic transducers, the flow meter canmeasure the average velocity along the path of an emitted beam of ultrasound, by averaging the difference in measured transit time between the pulses of ultrasound propagating into and against the direction of the flow or by measuring the frequency shift from the Doppler

          Working Principles

          Product

  >> Cable Float Switch

  The Cable type Float Level Switch is made from chemical resistant polypropylene. It is durable, low-cost,and specially designed to assist with long range and multiple point level detection in liquids. It is also suitable for tanks containing pumps and granular solutions.

          Working Principles

          Product

  >> Capacitive Level Sensor

  The principle of capacitive levelmeasurement is based on change of capacitance. An insulated electrode acts as one plate of capacitor and the tank wall (or reference electrode in a non-metallic vessel) acts as the other plate. The capacitance depends on the fluid level

          Working Principles

          Product

  >> Turbine Flow meter

  The flowing fluid impinges on the turbine blades, imparting a force to the blade surface and setting the rotor in motion. When a steady rotation speed has been reached, the speed is proportional to fluid velocity. Turbine flow meters are used for the measurement of natural gas and liquidflow.

          Working Principles

          Product

  >> Air Flow Meter

  Determining Duct Air Flow in CFM using the BAPI Pressure Sensor – Application Note. To calculate Air Flow in Cubic Feet per Minute (CFM), determine theFlow Velocity in feet per minute, then multiply this figure by the Duct Cross Sectional Area.

          Working Principles

          Product

  >> Horizontal Float Level

  Magnetic Float Level Switch Working Animation. The purpose of a float level switch is to open or close a circuit as the level of a liquid rises or falls. ... As a result, floats ride on the liquid surface partially submerged and move the same distance the liquid level moves.

          Working Principles

          Product

  >> Electromagnetic Flow Meter

  The electromagnetic flowmeter uses Faraday's Law ofelectromagnetic induction to measure the process flow. When an electrically conductive fluid flows in the pipe, an electrode voltage E is induced between a pair of electrodes placed at right angles to the direction of magnetic field.

          Working Principles

          Product

  >> Safety Switches

  Pull cord switch is mounted on the walkway side of the conveyor belt, preferably at about every 20 meters. When therope is pulled from any side. The switch is operated . Unless and until the handle is reset to normal position manually, theswitch remains in operated condition.

          Switches

          Switches

  >> Beltsway Switch

  Belt Sway Switch is a protective switch for detecting the meandering (sway or deviation) of belt conveyors, and sends out an alarm signal and an emergency stop signal.

          Switch Types

Calibration lab


>> We have Own Calibration Lab for Flow meter Calibration Up to 80mm line.

>> We Issue the Calibration Report As per the Standards ISO 4185:1980.

>> We also arrange NABL Calibration and FCRI Reports for all type of Flow measurments.


Certifications


     

Our Technology Partners